Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
I'm trying to implement DFU-OTA (Bluetooth transport) for our custom board and currently i'm facing problems in flashing the different elements (softdevice, bootloader, application...
I need to implement a PWM analyzer. I looked at the example in SDK 6 and it's fairly easy to follow. When I tried it, it doesn't look like GPIOTE handler gets called frequently...
I'm trying to backport the code form SDK 9.0 to SDK 7.2,
but i need to make sure that can be supported.
I found the "ATT-51", and there is a table about that,but the last...
ble_dtm.c has some bugs related to signed integer representation which prevent negative power (less than 0 dBm) from being requested in the vendor specific message.
...
Hi, all.
I'm using "SEGGER_RTT_printf" for debugging. Because have no uart port on my development board.
I want print double type variable like below.
double pi...
I am currently trying to communicate with a GPS module using the UART on an nRF51422 (using the Dynastream N548M5CB module). I am using SDK v9.0.0 and the FIFO version of...
Hi,
I want to send a continuous stream of data very quickly into the nRF51 through SPI and then dispatching it to a smartphone via BLE.
However I keep getting BLE no...
Hello
When i am in keil uvision 5.18 and use the pack installer all the examples using Softdevice S110 are gone in Keil. Is this a known issue and is there any way to solve...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
Hi,
It is written in the nf_drv_uart.h file for nrf_drv_uart_rx_abort() that
If Easy DMA is not used event will be
called from the function context. If
Easy DMA...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
Hi,
How can i get time stamp from RTC1 timer? While i am using app_timer + Softdevice?
Or any other way
Thanks and Regards,just to get timestamps from timer?
Faizan...
Hi,
I added DFU function to the example of ble_app_hids_keyboard according to ble_app_hrs_dfu.uvproj.
Test environment: nrf51822_xxAA, SDK_v6_1_0 and S110_v7_1, before...
