Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have installed nRF connect for desktop .In which I am trying to connect nRF 52 DK through programmer software. As soon as I connect the development kit via USB to type B...
I'm trying a project (nrf52) where I use both twi and spi to communicate with a set of sensors (each with a different protocol (twi, spi). after enablling TWI0 and SPI0 I...
Hi,
I've been trying to run the examples of the pc-ble-driver-py library, but I can't get them to run.
Every example gives me the following error: Please specifiy connectivity...
Hi team,
I am building AWS IoT client based on NRF52833 + Ethernet Controller.
I have done connecting and subscribing/publishing to AWS IoT broker successfully, and...
Hi there,
I am trying to set up a BLE communication between a central and a peripheral. For this I have succesfully used the nRF RSCS example from Nordic. But the problem...
hi dev
I'm not sure about beacon, so I'm posting questions to check.
General Ble process is like that
1) peripheral do advertise. during advertising interval, it sends...
Hello,
I was using NCS 1.7.0 and developed MQTT and SPI slave based sensor monitoring system using nRF9160 and want to switch NCS to latest build (2.2.0). A whole lot of...
Hello
Im traying to test the csense drv example , I want touch pad button only one
if I want to use this configuration
put the USE_COMP == 0 to USE_COMP == 1
now...
Hi,
We are working on creating a custom board configuration for ease of development. This is based on UBlox BMD-350-EVAL10. Which uses nRF52832.
While I created a custom...
Hi, I am trying to measure a sensor once a second. I require to use oversampling to get 14bits of resolution to meet our target. We are observing a large step in values that...
Dear all,
so far, for my external SPI NAND Flash memory chip development (Micron 256MB SLC NAND), I have been writing and reading data with my own, very basic level, flash...
I'm getting this error when I try to init the UART:
I have app_uart.c in the project, but a little investigation shows that it's not "enabled" in sdk_config.h.
When...
My current project is based on nRF52810. The nRF Connect SDK I found gives the idea that the architecture only works with GCC, according to the link https://developer.nordicsemi...
Hi,
I just bought a new PPK2. After installing "nRF Connect for Desktop", when I plug USB into PPK2, Windows 11 shows USB Device Not Recognized error.
I tried with different...
