Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi, We have custom nrf52840/33 peripherals, advertising every couple hours, and passing/receiving information from centrals running node.js version 12.22.5 with pc-ble-driver...
Hi, I work on custom board, which have NRF52833 and IS25LP016D SPI flash. I tried with SPI flash sample but SPI flash driver IS25LP016D was not found! err message show on...
Hello,
I want to use DTM FW for my design and have to update Tx & Rx pins to 21 and 20 respectively. Looking at the files in $\ncs\v1.8.0\nrf\samples\bluetooth\direct_test_mode...
Hi
I measured the CW output power of several DevBoards (nRF52832 and nRF52840) and the output power is much lower than expected.
Setup:
nRF52832 or nRF52840 DevBoard...
Hi Nordic,
when I run the samples/subsys/fs/fat_fs, the example of FAT file system usage with SDHC media, get error as below:
I have no idea how to fix it.
the SD...
Hello, sorry to disturb you I'm using Nrf52840 board and I would like to know how to flash correctly. I'm going to tell what i did with Visual Studio Code. I created a simple...
hello guys ,
In my project i am trying to reduce power consumption of nrf52810 with sensor. when a device is powered up it consumes 1.2mA without BLE advertisement and i...
We recently changed from nRF52832 to nRF52833 and for layout convenience used some of the P1.xx pins for our signals.
We are using SDK ver: nRF5_SDK_17.0.2_d674dde
For...
Just installed nrF Connect SDK v1.8.0 (using Toolchain Manager) - under Windows Windows 10 Entreprise
I have completed the setup and restarted my PC, however VSC is not...
Hi everyone,
I experiment with the saadc low power example . I have followed all the settings but I cannot achieve as low power as the example. As you can see from the PPK...
Hi,
1.How to test the ESD Human Body Model (HBM) performance of nRF5340?
2.How to test ESD Charged Device Model (CDM) performance of nRF5340?
Thank you for all your...
Hi everyone,
I have just purchased the PPK2. I've noticed that there two methods two measure the current
1. Source meter (the PPK2 provides power to the DUT)
2. Ampere...
Good day!
I have a question about length in MPID. In current implementation size measures in uint16 size and this brings lot's of troubles when you try to decode values...
Hi, I want to run UART on my custom PCB module that uses Wuerth Elektronik Thyone-I module that has nRF52840 chip. The project has just a RX, TX pins (and power supply, of...
