Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi All,
I need to send HCI commands from my uC to nRF52840 (with DTM firmware) via UART to for example set channel, Tx power, packet type etc.
Are there any examples/documentation...
Hello,
nRF52832 BLE project using SDK 15.3.0 and SoftDevice 112 v6.1.1. Circuit has the output of a comparator connected to two GPIO pins (COMPARATOR_PIN1, COMPARATOR_PIN2...
Hey guys, I'm currently working with NRF9160, developing code that requires a work-item to be scheduled within a time-frame (timeout value) that could go up to >24-hrs. I...
Hello,
I am using nRF52840 S140 v7.0.1 and using ble_app_blinky. I have a query on Secure Serial DFU if there is a change in Flash and Ram address.
In original example...
Hello,
I am using nRF52840-pdk with Keil5 and nRF-go studio for development purpose.
I am facing an issue that after new firmware version upload from nRF-go studio to...
Hi everyone,
Currently, I was developing an application on top of Zephyr. I notice that NRF52 SDK provides library for MQTT-SN protocol. However, my application needs to...
Can the TCLK timeout be changed? I have a ZigBee device that joins and performs a key exchange but then is forced to leave the network 12 seconds later due to a TCLK timeout...
I am working on a project that I need to scan bluetooth devices. I am using nrf52832 as a central, sdk 15.2 and s132 v6.1.1. when I activate the advertiser tab on nrf connect...
Hi,
I haven't ran the FOTA download library in a while and I was just testing it. I don't seem to be getting any of the FOTA_DOWNLOAD_EVT events. I am running nRF SDK v1...
I am using nrf52832 as my cnetral and also nrf52832 as my peripheral . i am connected central with peeripheral using ble multilink example code. but it shows only 16bit uuid...
I am using nRF 9160 mqtt_simple example to connect to a custom mqtt broker address as shown below
The following is the mqtt.fx application
I changed all the necessary...
Radio callback not occure after advertising stops.
I changed ble_app_beacon example to support timeslot as follows.
I put "NRF_LOG_INFO("radio_callback:%d", signal_type...
Hi, We are using nrf51822 in our device and Device firmware update is implemented in it and we are being able to do the device firmware upgrade by using nrfConnect app. Now...
