Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
We are looking for a 2.4Ghz supported module with Programmable Frequency Deviation. Is there a product that we can consider from Nordic Semiconductor for this?...
Hi, We are working with integrating LoRa to our nRF52840 with BLE and FreeRTOS. To be sure that LoRa worked as expected, we configured and tested LoRa on nRF52840 dk and observed...
Hello,
I'm using nrf52840 and i would like to ask if it possible to use the I2C bus without external pullups. I mean, i would like to avoid using external pullups
is there...
I am using a NRF52840 DK with a SoftDevice S140 6.1.1. I have also flashed the secure ble bootloader on the device.
I have been using the nrfprog command line tools within...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
Hi
I have installed every requirement for the device. I want to know how to run the blinky example on the device. I can not find the SDK which has the example plus can I...
Hello, I'm currently developing a PS2 code to read the inputs of a mouse and transmit it over BLE, nrf_delay_us() is giving me a fatal error every time according to debug...
Hi,
I am trying to implement Generic HID that can transmit/receive data like CDC using the generic HID example source of nRF52820 SDK 17.0.2.
But I can't do both sending...
Hello everyone,
I'm a fresher of nRF52833. I'm facing a problem like this:
I want to read some information in Terminal but In my product I only have USB I/Os (D+ D-)....
Hi,
I'm trying to use the nRF91 as a Modem for an Arduino. Is there some example on how to use the AT commands of the serial_lte_modem sample to send a HTTP (or at least...
I built an application for the nrf51822 on top of SDK12.3, to which I added the buttonless DFU based on the "experimental_ble_app_buttonless_dfu" example.
As a boot loader...
Hi,
I want to increase the amount of BLE MIDI packages I am sending. Softdevice 132 nrf52832
MIDI data is sent by notifications and updates of the characteristic value...
Hi,
I want to use uart async on the nrf9160, I get the following linking errors at build time:
here is my prj.conf
If it's defined CONFIG_UART_INTERRUPT_DRIVEN...
Hello,
I have a question regarding the nRF5340 microcontroller or similar. Usually, when programming UART, I2C or SPI bare metal, one is using interrupts, register and buffers...
