nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi
I am using a buttonless DFU to do OTA for my application. Everything is working fine up to now, but now my custom board got few modifications of using PIN 16 for USB...
I am trying to complie Eddystone project which is part of NRF5 SDK and when i compile the project in Embedded Studio I get the following error
/resized-image/__size/738x210...
Hello. I am developing with the following configuration.
In this configuration, since it is necessary to connect multiple peripherals with multiple roles, "scan_start...
Since migrating to the Zigbee 3.1 SDK I have noticed a few oddities with the behavior of attribute reporting that I am thinking are related to the following bugfix:
The...
HI,
I find that the DFU code start address regsiter is different between SDK15.3 and SDK16
SDK15.3
MemorySegment name="uicr_bootloader_start_address" start="0x00000FF8...
Hi,
I'm using the Home Automation profile of the Zigbee protocol and, in particular, I'm developing the Window Covering Device, present in the SDK "nRF5_SDK_for_Thread_and_Zigbee_v3...
It appears the softdevice gets into a strange state when a BLE connection is lost while transferring data. How does application code reset or reinitialize the softdevice ...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
Hi,
I would like to setup my nRF52840-Preview-DK as a central to communicate with a peripheral device via UART over BLE.
Once my peripheral device is connected it writes...
