I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am having some trouble with sending messages using MQTT on nRF9160DK. What I ultimately want to to is read UART and send whatever I receive to an MQTT broker. When running...
I am trying to use sd_ble_gatts_hvx function to send custom data through BLE. I found out that for the data I am sending the function takes a lot of time to send data which...
My custom nRF52840 board uses the STmicro STM6601 push-button controller. To keep the nRF powered, the PSHOLD line must be kept high. I have a GPIO set as an output for that...
Hi there,
I am trying the test the robustness of a BLE use-case. This means that i have to create error scenarios and further observe and analyze how it's possible to recover...
Dear all i have a very funny situaton.
I can only send 1 byte in my service data when I increase it to two bytes it doesn't send. and says invalid parameters
When...
In the right process，like this：
but my program is ：
i lost “Sent Read By Group Type Request, GATT Primary Service Declaration, Handles: 0x0001..0xffff” .
in the...
Please kindly help to push this emergent issue!!!
We detected CLK signal using oscilloscope as picture below:
We can see that clock frequency is set to...
I have been making good use of the Power Profiler Kit with some impressive results on my nRF52 project.
I would now like to extend the testing to view an application where...
Hi
I have some question about DFU for Mesh3.10.
1.How to update Softdevice or Bootloader?such as I'm going to update SD from version 6.0.0 to 6.1.0.
2.Because my firmware...
I am trying to port pc-ble-driver-py to soft device version 6.1. I have made changes to python code to take care of changed API signatures, new constants etc.
When testing...
Hi,
I am using nrf52832, in the ble_app_uart_c example, i want to use rc source as a lfclk,
i changed the following parameters in the sdk_config.h:
NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I have developed a custom PCB using nRF52832. It's meant to work as an ibeacon currently and consequently works in a non-connectable, advertising only mode. I will...
Hi,
I am trying to use GPIOTE_PIN_HANDLER in the master nrf52. What is the correct way to read data from slave?
Slave device is sending data using nrfx_twis_tx_prepare...
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using app_timer_create() to create low power...
