the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi guys!
I want to select NRF52840 as my target platform. Is it possible to start software developing on 52832 (for which I have devkit) and then seamlessly move my code...
Hello, I want to do a project with Segger Embeded Studio using the nRF52840 with the SDK_Mesh I have 2 nRF52840 cards and I want to transmit data to a mobile phone using a...
i compiled the ble_uart_app project it got downloaded in to the NRF51DK but the bluetooth is not getting turned on ,usually the output of this example is LED has to be turned...
Thanks for your support folks!
I am trying to read some bytes I have wrote in a MX25R8035F. From the datasheet, if you send 0x03 (READ) + 3 Byte address, then the memory...
Hi,
We want to receive the data in laptop over the BLE like nRF UART mobile APP.
we sending and receiving data in Mobile app but we can't get the app for desktop.
we...
Hi,
1-I did some test for nrf51422 (SDK12.3 + soft device S130) power consumption. result as below:
-system on sleep mode( without UART and BLE Advertise ):90uA
-system...
I am working on developing BLE app using connection oriented channel . I am using nordic semiconductor as a peripheral device and iPhone 6 as central manager.
I am able...
Hi,
I am working on a project that requires extremely low power consumption (20-50 uA) at max. We are currently consuming around 5.5mA. The project uses SPI to communicate...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to check mesh network. I want mesh example code using keil IDE. I am using SDK12.3.0 and Hardware is nRF52...
How can i calculate the average current consumption, so i can estimate battery life.
This application uses Gazell to send data.
Peripherals used:
-UART for logging ...
Hi
I would like to connect the nRF52810 to 2 devices via UART interface by switching the Rx and TX GPIO pins by the software in realtime.
Is it possible? what is the method...
Hii
I m using Fanstel Ev board (BT840F) using nRF5248 Fimware.
i want to set maximum transmission power +8dbm in FANSTEL Ev Board but i got an error code 7 is Indicate...
Hi,guys.
In my experiment, Firstly,I creat an app_timer work every 20ms interval
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false); err_code = app_timer_create...
Hi everyone,
Recently, I used the nrf52832 learning board to learn SDK13.0.0, when I see SAADC, tell the truth, this exampe is a bit difficult for me to understand.
My...
