Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi Everyone,
I am trying to record data from ADC to a SD card every 500ms using nrf52832.
I am following the fatfs example. Before I had a problem whereby every approximately...
What are the most recent set of software tools that are known to work on OSX Sierra?
Any pointers to a good IDE for debugging will be great. I understand there are many questions...
Hello there,
I'm trying to learn how to use some of the perepherials of the nrf52832 with the DK,
trying to learn a little about the SAADC I found some example modified...
Thank you for reading my question.
peripheral project :ble_app_hrs_rscs_relay，SDK14.1 ,S132
client project: another manufacturer's soc
I set peripheral peer manager...
Hi,
I am testing with ble_app_uart . my board will advertising to my phone . I realize that if I don't connect 2 pin uart on NRF board to USB TO COM to my PC . Then , my...
Hi,
Are there any examples of SDK examples that work with USB BULK communication?
Which example should I use to make usbd_hid_generic example work with BULK communication...
Hello,
We are using Nordic SDK 11 MQTT adapted for TCP/IPv4(separate module) . It works fine without TLS. I added the flag "MQTT_TRANSPORT_SECURE" and made adaptations...
Hello,
Question regarding using the SPI master peripheral with DMA to communicate from the nRF52832 to the ads1296 device .
In order to use this device in the mode and...
Hi engineers, Here we are facing a critical problem in which the NRF51822 stops handling/processing the GPIOTE->PORT interrupts after some days good working. This problem...
I have a project which needs to be built in IAR, but uses the signed bootloader. I understand, that if I want to flash and debug the application from within IAR, I need to...
Hello,
In my next project I plan to conductive pads as buttons(that are exposed for humen touch to interacte with the) one is connected to ground and the rest will connect...
Hi,
I am using SDK v14.1 for nRF52840.
The secure_dfu_usb debug example works well when the J-link RTT Viewer is connected.
But when the RTT Viewer is disconnected the...
Hi everyone,
I would like to know if it is possible to establish a serial communication to a PCA10028 card using Adafruit Bluefruilt LE friend knowing that there is no...
Hello everyone,
I am using nrf51822 chip that has functionality to flash bl, sd or app using mobile app application. I want to reuse this functionality in order to have...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
