Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I have a hard time understanding precisely what an Element is and how it differentiates from a Model when talking Bluetooth Mesh.
The only definition can seem to find of...
Is there any way to detect / prevent the use of range extenders?
When using a central & server with low TX power, the range is say 10m.
Now an attacker can use a relay...
Hi all,
I have been using Nordic chip-sets for a while mainly for BLE applications. I am now developing a simple lighting product based on Nordic nrf51 family chip-set where...
hello!
i am working with the component nrf52840 v0.5.1 and i need development a thermal profile according with the datasheet of the component nrf52840 v0.5.1
could you...
I'm using op-amp(LM358), condenser microphone and PCA 10028.
My project collect output values of op-amp and broadcast that.
But, noise was occurred while it is advertising...
I'm using the ble_app_multilink_central example app.
In the pca10400.h I changed #define BUTTON_PULL to NRF_GPIO_PIN_PULLDOWN.
The problem is that the first pin interrupt...
Hi
I'm creating an android app for smartwatch(used nrf51 ble),I have two questions
1.I used ANCS(Apple notification center service) in my android app,but nrf51 device...
I'm using the SD (nrf52) MBR to update our custom bootloader, in a battery powered device.We have some custom hardware which is used to disable our LDO, to enter a "Ultra...
Hi Everyone,
Recently I have been trying to measure the current consumption from the dev board.
I have set up the board as instructed by cutting SB9 and soldering SB11...
Hi,
I see intermittent incorrect values from the saadc. The code is described here .
The graf shows battery voltage in mV over about 4 days with one sample per minute...
I am getting following errors when compiling source code in Keil-5. Any one suggest me what i am missing to define symbol?
linking...
._build\nrf51422_xxac.axf: Error...
Hi,
We have devloped PCB based on nrf52832 as beacon.
We have also developed firmware for that and it will advertise for some and than go to sleep mode and after some...
Hi,
What is the minimum number of symbols in preamble nRF52840 has to receive in order to receive full packet on Coded PHY? I can see that it can easily receive packet...
help! Thanks
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
chip:nRF52832
we found that the pstorage's callback will not be triggered when the Bluetooth...
