I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
hi all,
i am a begineer to nordic. i want to send data over ble and read that using master control pannel.
please say wat api i want to use and how to use. please give detail...
Hello I'm new of nRF seriese.
nRF51822CEAAD00(0x004d)
SD130 ver2.0.1
kail Ver5.18
SDK11.0.0
I just finished the tutorial and now I'm making my new project with twi...
Hi, I am using Heart Rate rate monitor code to send floating value instead of unit16_t.
I am using the heart rate service to send the data. Instead of using simulated sensor...
Hi,
I am new to nRF5x BLE devices.
I need to create a project and would like you to help me out.
I need to connect two nRF51822 devices. If one of the devices goes...
hi dear officers
since the datasheet states that value 1 stand for connected, does it mean this pin is active-low.
in order to physically reset the device, could i connect...
I have tried ble_app_uart_c project in SDk 9 , SDK 10 or SDK11 , but they have the same problem.
Problem is that slave(SDk 9,ble_app_uart) can send data to master(by terminal...
While trying to bond an iPhone 6 (running nRF MCP App) with an nRF52 with S132 2.0.0 I encountered the following error:
On the first try, when the iPhone is not yet paired...
I am trying to set up a button interrupt by adding the following functions:
void button_interrupt_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_gpio_pin_toggle...
Dear Sir,
When nRF51822 is a slave, it should be updated software through Master(Z-Wave CPU) remotely.
How can we update SoftDevice software in nRF51822? UART, SPI, or...
My code detects an external signal using GPIOTE. Whenever the signal falls, GPIOTE calls a handler, audio_stimulus_handler . The code is shown below. Essentially, after detecting...
I have a nrf51-dk. I would like to the pincode to be stored in some configuration settings which is written in non-volatile memory. I do not want the pincode to be hard-coded...
