Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
In past , I was able to perform DFU-OTA over BLE transport for a custom board that has nRF51822QFAA (256kB main flash memory) SOC. I tested this functionality with Nordic...
I am trying to setup a nRF51422 Development Kit (PCA10028) v1.1.0 board with ble-sniffer_win_1.0.1 sniffer. I programmed the Dev board with firmware version ble-sniffer_nRF51822_1...
Hi all,
I am using ble_app_uart application to send data to a Bluetooth device. I am sending the data to the Tx Rx Pins of nrF51822 module via an external controller. My...
Hello forum, I've been trying to get SOME alert on my nRF51DK from a phone. I first tried the alert_notification example, but it appears that one has to write a custom Android...
I'm trying to build the blinky example in SDK 11 and load it onto a PCA10000. I'm using the make file in PCA10031/blank/armgcc and am building this under linux. If I use blinky_blank_pca10031...
Hello All,
I am using nRF51822 with SDKv10.0.0 and s110 soft device with RTX os. My project have 5 different threads with 1000 bytes of memory is needed in each thread...
Hello,
I have a project where I wish to have BLE operation while active and use RTC1 as a calendar keeper while in low power mode. So far as I have seen, the softdevice...
Hi all,
I am currently working on the nRF51422 with the S110 version of the Softdevice. The SDK version is 8.1.0.
I tried to get some information back from the Softdevice...
Hi, i am new to embedded system.I want to use nrf52 DK as master and connected with two slaves by two spi channels. since in hardware design, I have designed the chip with...
Hi All, Am using NRF52 and SDK 11.0.0.2 alpha ,
I am using two profiles. I need to Advertise with specific name and parameters for each profile. This profile switch has to...
Hi,
I want to program the nrf51822 with C++ and from what I've found here it should be possible.
But nrf_drv_gpiote.h contains designated initializers wich aren't supported...
Hi. I use SDK 9.0.0 and Softdevice S130 1.0.0.
I try to pair Scanner and Peripheral. Scanner use example code "ble_app_uart_c_S120-master".
My peripheral have function...
