I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
I am using the SHT21 sensor for measuring temperature and humidity, trying to connect it to nRF52840 DK Board using TWI mode.
I am unable to even scan and get the response...
I deleted the flash completely for the bootloader example, then I installed soft device. The softdevice area for nrf52832 is written as 148 kb in the documents. In nrfgo studio...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
