I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I'm trying to test PWM with a simple example, I've edited spm via adding
KConfig:
spm.c
I'm getting the output at the boot as;
I assume that PWM_0 initialized...
SDK: 14.1.0
CHIP: 52840
MULTI PROTOCOL
Hi, I want to know zed rf on off switching mechanism and configure on/off interval time.
I(current) - t(time) graph
What...
Hello there,
I am experimenting with with the gpiote and ppi examples, and have a couple questions regarding the member variables of the nrf_drv_gpiote_in_config_t struct...
Hello,
I planned to to use in my design 1.8V. But for redusing power consumption of nrf5340, which way is correct and prefferable:
1. Use external 1.8V supply in normal...
Hello,
in file nrfx_gpiote.c there is a fatal error which overrides data because of a false array index.
nrfx_gpiote_init there is a for loop which calls the function...
Hi All:
As the topic...........,I want to set up DFU with usb,how? When I edit the USB_HID_KBD to USB_HID_GENERIC in usbd_hid_composite example,it makes some errors:
1...
Hi everyone,
I am working on the USB_MSC example and I need your advice. I read an IMU unit and I want to store the data into a file. I create a single file to store the...
I am using nRF52832 evolution board and SDK version 15.3.0 in Segger studio(Ubuntu system) for Interface LSM6DSL accelerometer using I2C.
I am use TWI peripheral example...
Hi,
I want to program a nrf52832 module and a J-link debugger is on it's way. Until then I wanted to use my Black Magic Probe to flash and debug the application. I can successfully...
Hi,
We want to choose which frequencies we should implement on nRF9160 to have the best frequency bands coverage. Would you have a list of all known frequency band used...
I want to use the sensor example to transmit 10bytes of data at at rate of 10Hz.
I have tested the publishing using periodic publishing configured with the nRF Mesh app...
Hi,
There are many undefined reference error with file nrf_atfifo.h, already checked Makefile.am is included, please help to advice if there any file is missed.
........
Hello,
I'm using the following code to communicate my NRF52-DK with pc.
But sometimes the DK transmitting repeat data and sometimes error data is sent(missing 1 byte)...
Hello,
I'm implementing libuarte with ble_app_multilink. But receiver side receive gibberish like below.
It looks like RTT message is printed to serial port. But I...
I am using nrf9160 for a monitoring project using NB-IoT network. The problem I am having is when I go to an area where there is no NB-IoT network, the device crashes often...
