I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
I'm using SDK 15.2. The bluetooth disconnects when I enable notifications on nrfConnect. This happens only if I increase the number of bytes to be sent. I'm writing...
hii,
i am currently using light switch example proxy server and proxy clients.
here i am using 3 boards ,2 board(node B &C) are programmed with 4 generic onoff servers...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I specify a hex file in "Project Options"-> "Debug"-> "Loader"-> "Additional Load File [1]". With this setting...
I have a question about TX Power.
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
The device operates as a “Peripheral”. Is there a way to know...
Hi Devzone!
I merged app_multilink_central and app_uart_c on central side and used app_uart on peripheral side.
I'm using 2 peripherals and 1 central now, and those can...
Are there any examples for disabling/enabling peripherals at runtime for low power purposes on the nRF91 on ncs v1.0.0?
I've seen these threads but they didn't have the...
Hi all We are using nRF9160 gone through all tutorial like GPS,GPIO peripherals,Led blinking Now my main question is How to use PSM mode and eDRX mode program for nRF9160...
I am having trouble getting the nRF9160 DK to find a network running the Asset Tracker than came in the device. It appears to reset after 15 seconds of LED 3 blinking. I can...
I am trying to read from the modem on the nrf9160 DK using the AF_LTE socket and am running to a problem with reading the response from AT+CLAC. I've chosen that command to...
I have been exploring BLE and I am using bt_gatt_discover in my zephyr-based central device (nrf9160) to list the services on a Thingy:52. I am getting the callbacks as expected...
Summary
I'm running into an issue where in certain cases peer manager reports the presence of peers, but when those peers are added to a whitelist I get an NRF_ERROR_NOT_FOUND...
I defined an integer value _ALIGN(4) uint8_t sixteen = 16 and assigned sixteen to a FDS record that is later assigned to the p_data of a custom characteristic. However, when...
I updated to v10.3.0 of the nrfjprog and mergehex tools and I've noticed that the behavior of the page erase command takes far less time when it gets to a certain region of...
