I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
We are using a NRF52840 chip (SDK 15.3) in an application where we use the softdevice (S140) in combination with 2 UARTS: one for sending out debug output (UART0 - nrfx_uart...
Hi, We have a nrf52 which runs some project using ANT, now we would like to implement BLE for UART communication between a phone and the unit. The code base is already extensive...
Hi,
I just connected an nRF91 dk to nRF Cloud, which worked fine. However, for some reason the GPS says I am in Trondheim, while I am clearly somewhere else in the world...
I try to communicate with NRF52832 with NRF51822 for the example radio receiver and works well with SDK5 12 3
when I try to communicate with E73 (NRF52840) board(E73(2G4M08S1C...
How to push Initiator to resolve its private address (seen at direct_addr of adv_report) when bonded private Advertiser does a direct advertising?
I need the only Initiator...
I've followed the procedure on the nRF connect cloud to verify the SIM card and add the LTE device, only once the LED3 and LED4 blink at the same time like it was connected...
We are using a NRF52840 chip (SDK 15.3) in an application and are having issues with the startup of the board. I managed to create an example application where I integrate...
Hi. I have attempted to add an out endpoint to the HID usb generic example (only 1 in endpoint in example as it is a mouse).
However it is not working. When connected my...
Is there any UART examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
Hi, I measure current in beacon in Long Range mode. Behind 3 current peaks witch represent TX on channel CH37 CH38 CH39 there is a strange current peak, witch I don't understand...
Hi,
I can't build any samples anymore for my nrf9160-DK using neither SES nor CLI only.
I followed the "Getting started assistant", pulled the v0.4.0 version of the SDK...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
Hi,
I would like to run the radio_test example on an nRF52811 chip for certification purposes.
What changes are required on the latest sample code and project to get it...
Hi all,
Is there any example to discover the custom UUID services with pc-ble-driver c/c++? As far as I understood, the ble_db_discovery is not supported for this driver...
