I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi, everyone,
We are developing the project on nRF52832 chip that is built from master (multirole) and slaves modules. The master program (in our case master is multirole...
I want to send data to all node by mesh 2.1.1.
From the Mesh profile(3.4.2.4 Group address),the dst_addr = 0xFFFF is send to all node .
I try to setting "packet_tx()"funtion...
Hi,
Currently im working on creating firmware for out device based on the nrf52832. I have structured my project where i have seperate files for each module i am creating...
The hid keyboard example includes the battery service. But how does it work? I would like to monitor the battery charge. After I use the voltage divider, to which AIN pin...
Hi,
I have NRF51DK (PCA10028) board and i want to flash BT832 (NRF52832) device.I have downloaded latest SDK but it only has the option of PCA10040.Is it possible to flash...
Hi All,
I've problem with nRF52 programming. I want to verify uart by using examples placed in the NS SDK for nRF52. After I loaded uart example, uVision shows error in...
Hello,
I am looking into the Power Profiler Kit for measuring the power consumption of a custom hardware. I can see that the PC Application is really useful during development...
About this example
https://github.com/NordicPlayground/nrf51-ble-tutorial-advertising
It´s advertising the data
uint8_t data_response[] = "Many_bytes_of_data" with the...
Hi,
I was working with MCUBOOT and was curious too know from where the MCUBOOT release version number is been generated or fetched-
When building MCUBOOT using cmake...
Hello mates,
I am modifying the Light Switch Client and Server example, to send messages uint8_t from the client to the server instead of use bool on_ff with no luck yet...
I am currently using a 51dk board. I am trying to study low power system_on_wakeup_on_gpio in github. I built this code and measured the amount of current. I would like to...
Parameter setting code is shown below. I've verified that the settings are being reported back in events, so they seem to be taking place. However, I'm keeping track of the...
I am trying to get the application to enter DFU via the buttonless DFU service using SDK 15.2. It appears to be stuck because of an SVC call not returning. Both application...
Hi :)
I would like to test the nRF52840-Dongle in a Raspberry Pi 3B+ OS = Rasbian (the bluetooth 5 features: 2Mbps and Long range). but unfortunately I didn't find a nRF...
I'm looking for a gateway (or BLE 5.0 device that can connect to a gateway, e.g. USB dongle) that uses the nRF52 series solutions with an amplifier that brings the transmission...
