I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hello everybody,
I can flash my custom nRF52832-based PCB using the nRF52 DK and Segger Embedded Studio or nrfjprog, but this requires that I always have my computer with...
Hi,
I need to get 1.8V on the VDD using high power mode. According to the documentation this is the default value. However, I measure 3V.
Please advise,
Daniel
I am developing a nRF-Mesh based product. This product consists of a fixed number of nodes in a Bluetooth Mesh Network. Are there possibilities to factory-provision a set...
Hi!
I am working with experimental_ble_app_eddystone in SDK 12.2.0 for nRF52.
I have seen that the firmware does not support using different advertising inteval for each...
I'm wondering whether or not nRF52840 can be used for a USB smart card development.
"According to the spec of a USB CCID device (which could be found on www.usb.org ), there...
Hello everyone,
After using IPSP intiator and IPSP Acceptor BLE Examples on 2 different kits and connecting them through this profile, how do i send IPv6 packets between...
I cannot get a connection between Seeger Studio and a dev board from Seed Studio called nRF52832-MDK
I have added a pull-down resistor on TDO as I was getting an error that...
is advertising Complete List of 128-bit Class UUIDs(0x07) a doable ? I mean like " Complete List of 16-bit Class UUIDs " (0x03) it's not a service, just has an information...
Hi,
I'm debugging a Nordic mesh example, which is named light_switch_server_nrf52832_xxAA_s132_6.0.0_Debug, after build and go, a message appear:
sd_ble_enable: app_ram_base...
Hi All,
Hoping this is straightforward for an intermediate developer.
nRF52840-DK (matched dongle not yet in use), SDK 15.2.0, SES 4.10a (Jlink 6.40), Windows 10.
My...
Hello,
I have seen that the nRF52840 PS v1.0 specifies the RSSI_PERIOD to be 15us. I have also seen that the nRF52832 has only a RSSI_PERIOD of 0.25us (PS v1.3+) or 8us...
I need some technical information:
- the micro Host can (through a pin?) make WakeUp of the BLE module to configure it / change the operating parameters etc? - the BLE module...
While visiting the Nordic Tech Tour we were discussing the pros and cons of BLE Mesh with a Nordic employee. He recommended that we also looked at a different solution, a...
This is essentially a repeat of :
https://devzone.nordicsemi.com/f/nordic-q-a/38808/is-a-3-bit-synchronous-3-data-lines-clock-parallel-input-at-16-368-mhz-feasible
Instead...
