Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I want to change the advertising timout during runtime. We have two use cases for our device:
Batterie mode --> advertising timeout = 2min
Power...
Hello,
Implementing a LED led driver was pretty simple and below code works well:
nrf_gpio_cfg_output(LED_PIN);
nrf_gpio_pin_clear(LED_PIN);
NRF_GPIOTE->POWER =...
Hi there,I am using the PWM library in github github.com/.../nrf51-pwm-library . After I do this in my project and I check the pin output with Oscilloscope but didn't see...
I have a product that was released a few months ago and is operating in-the-field. Recently we discovered a bug and need to fix it. We are unable to do a DFU because:
...
Hello,
DEVICE_MANAGER_APP_CONTEXT_SIZE should be less than 256 bytes in size.
However, it seems to work properly (not fully tested) whith a size of 800 bytes, and no more...
Hi all,
I want to make sampling from microphone at 16KHz. So I want to first disable softdevice, do all measurements. An after that enable softdevice to transmit data. Will...
Hi,
Recently, I am playing around with the NRF51 dongle and trying to make it work as a BLE master.
However, when I run the sample code(e.g. advertising, multi-link .etc...
Hello, i am seeing a strange behaviour of pstorage module and i don't understand what is happening. I have read links below:
pstorage-problem-on-power-off
saving-data...
Hi,
I haven't been able to find a clear answer to this.
With the ESB protocol, a payload can be stored in the PRX TX FIFO to be sent back to the PTX as part of the ACK...
I have some nrf51422s beacons and wondering if they can send and receive data. So I want it to keep transmitting its id and signal strength but if somebody is reading the...
I am trying to implement the ANT+ Environment Profile using the nRF51 DK and I was wondering if anyone had done this and could point me in the right direction to start. I...
how to synchronize multiple NRF52 them?
Should I use a router? What route do you recommend for development?
Otherwise many people tell me that the Bluetooth has a very...
Hi all,
I create 4 timer in APP, and there seem only one timer (work in single shot mode) can not trigger by right ticks.
I add some log and find that:
First I...
Noticed in ant_parameters.h
#define MAX_ANT_CHANNELS ((uint8_t)15)
First question: is this correct for nRF51?
Second question: is nRF51 going to support 15 channels...
