Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
I have been experimenting with mbed ble programming and have had some success with the examples and my own programs. Everything works fine on the nRF51 dongle and DK.
I...
I'm trying to enable the active signal for an nRF8001 on Adafruit's breakout board. Is there a way to do this without using the nRFgo software? I use a Mac so setting up nRFgo...
Hello.
I use BLE Shield V.2.1 of RedBearLab.com for Arduino.
The shield equipped nRF8001.
After about 62ms from reset nRF8001 by putting Low signal in Arduino pin 4...
Iam using NRF8001 in my project & i don't know how to enable them & connect them through Android app basically iam using in tracking chip so any one have a idea that how to...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
Hi,everybody!
Recently,i use nrf51422 as peripheral programming s310 ant_ble_hrs example in sdk6.0 and use nrf51822 As center programming s210 hrs example in sdk6.0. I find...
Suppose I have a lot of very small characteristics (1 or 2 bytes) to send lots of notifications on. They are all updated simultaneously, though the central doesn't care about...
It seems daft, but the ble_heart_rate_template_with_battery_service example in the nRF8001 Arduino SDK does not use the nRF8001's Battery Monitor!!
Instead, it just uses...
