Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello, I am using the examples\ble_central\ble_app_hrs_c project from SDK_8.1.0 with s120_nrf_2.0.0 on an nRF51422_CEAAB00. This when the variable m_scan_mode set to BLE_FAST_SCAN...
Hello Noric expert.
I am stuck with writing data to flash. I am using nordic's nRF51-DK.
My sdk version is 9.0
Could you go over my code ? My code is attached.
...
i have successfully uploaded my custom made file to my nrf51422 sdk v8.0 and softdevice s110 using DFU/bootloader. but when i try to upload my file 2nd time i got an error...
Dear Developer Zone
I have searched now a lot in the Internet, mostly the say it's possible to reprogramm the Firmware of the nRF51822. I have such a chip and a JLink Debugger...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hi,
What is the minimum current draw required to keep on internal DC/DC regulator in nRF51822?
In S110 SoftDevice profile, is it possible to keep on internal DC/DC regulator...
Hi,
I developed an application for nRF51822 starting from ANCS example.
All works fine but I have current scenario ... starting from a clean situation ...
Execute...
i use demo ble_app_multilink_central and ble_app_multilink_peripheral ,in SDK 8.1.0,but when i use sd_ble_gap_connect (S120 to S110)return NRF_ERROR_INVALID_STATE ,
why?...
I am checking values of my PCB with an nRF51822. VDD = 3V. AVDD ~= 800mV
I was expecting a the AVDD voltage drop to be much less. What should the AVDD voltage be? What...
Hi,
I want to design one BLE braodcaster and one BLE observer using nRF51822 chip.
What should be the advertising interval time and receiving interval time (with receiving...
Hi:
I am using the ANCS from SDK9.0 ,SoftDevice8.0 and iOS8.1.3.
Every time when I run ANCS, SPI will often crash.and error codes is:NRF_ERROR_BUSY.
Don't know if...
Is there any extra requirements When a Android APP connect to my Ble Decice? I want connect to my Ble device(51822) by my Android APP(EZ-GUI Ground Station V3.208.208), But...
