Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi.
I try to build the nrf_audio sample as BIS headset with enabled FOTA and NCS2.7.0 and get the following link error for the ipc_radio image:
FAILED: zephyr/zephyr_pre0...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...
Hello,
is there any technical reason why the MPSL radio notification API has been dropped somewhere before NCS 2.6?
Our application needs information about radio notifications...
Hi, I'm looking into a design based on the npm1300 and nrf5340 for a battery-powered wearable device.
We would like to use two buttons (A and B) as the user interface with...
We have nrf52840 S140 BLE Central device that currently connects to TI based sensors. I have implemented code that can upgrade those TI sensors' firmware using the TI BLE...
In BLE Fundamentals, Lesson 3, Ex. 1 (BLE connection exercise), the nRF84020 DK board indicates a successful connection (led 2 is on + connection message in serial terminal...
Currently, I am creating a CIS-connected device using nRF5340 Audio on a homemade board.
Since the circuit configurations of the Gateway and Headset are different, I have...
I just got a fresh Win install and installed a new version of vs code (details below) and lo and behold the nrf welcome page is empty! Apparently, this was changed a while...
Hi I am looking for some advice with regards to getting a Fanstel BU840XE ( BU840XE, The longest range, Remote USB Dongle for BLE 5, Thread, Zigbee — Fanstel ) device to function...
Hi team,
I am getting secure fault after PPP started in SLM (v2.6.1) application.
here is the snapshot of the error message
Anyone having same issue and resolved please...
I am experiencing an issue with the I2C device on the nRF5340(our custom board) where it is unable to read/write to the sensor, resulting in a return value of -5.(EIO)
Details...
Hi
I'm chnaging the Secure Bootloader to an external falsh for bank1, connected with QSPI.
In the function on_data_obj_write_request is the call for nrf_dfu_flash_store...
Hi,
I have a project with an nrf9160 running zephyr. Can codechecker be set up in the build in nrf connect in vs code so that when a build in vs code is done it runs code...
Hello,
I am migrating an application based on the old Nordic SDK16 to the NCS Zephyr SDK.
My workspace is using Zephyr commit f8f11338, nrfconnect/mbedtls commit de1b3f57...
