I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
I‘m a rookie for the matter.I use nrf52840 In the matter lock case,when i press button 4,it will start adv.But it did't start.
so i want to add config log to debug,But...
I am attempting to stream data in chunks of 65535 bytes from the nRF9160 using data mode from the 2.6.1 version of serial_lte_modem sample code. The nRF9160 receives AT commands...
I followed the MacOS command line installation instructions at docs.nordicsemi.com/.../install_ncs.html
After running `west update`, it says the tree structure should be...
When following instructions for setting up the NRF52840-dongle as RCP coprocessor , I'm getting this error: ModuleNotFoundError: No module named 'intelhex'
Full log...
I have some initial questions regarding the nPM1300 :) :
- It is possible to download the nPM1300 datasheet as a PDF file instead of viewing it online?
- Regarding VBUS...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hello All,
I have nrf9610 Develoment Kit on my side:
mfw_nrf9160_1.3.5
Using nrfutil-device core version: 7.13.0
Using nrfutil-device version: 2.1.1
...
When I do a sd_ble_gattc_char_value_by_uuid_read I can only get a maximum of 253 bytes.
And when I read more I get a gatt_status of
BLE_GATT_STATUS_ATTERR_INVALID 0x0100...
when testing NIDD on NRF9151 we are using sock connect -f packet -t raw but it is giving us error
mosh:~$ > sock connect -f packet -t raw sock connect -f packet -t raw Socket...
Hi,
In the NCS V2.3.0 version, I successfully obtained the serial device through the following code and compiled it But when I get the serial device in the same way in NCS...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
this is the last log message from monitor thread, I never got any error message from the thread.
00 > [ 01:37:03.890 , 808 ] <dbg> monitor: print_die_temperature: CPU...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
We have power ceilings configured as per the last nRF7002 Product Notice :
Yet we are seeing values below expected (around 13 dbm):
We noticed upgrading to 2.7.0...