Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I'm having trouble reassigning the pin value for the LED's in the connect SDK. I am using the base PWM Blinky example and have changed the pin value assigned to PWM_LED0 in...
Hi Team,
We would like to connect external LEDs to the NRF52840DK controller.
We could not find any unused GPIO pins to connect.
We have referred manual but it showing...
Hi guys. From the ble_app_hids_keyboard_pca10040_s132 (nRF SDK v17), there were several HID characteristics added.
protocol_mode_char (Protocol Mode characteristics) ...
Hello, Not sure where to direct this (we can open a GitHub issue but wanted to clear it here first), basically everything works great on our Galaxy Tab S6 Lite ( SM-P610)...
Hello,
i am new with the nrf9160, and we are using the download client to download a firmware for a secondary mcu. At the moment its implemented so that at the begin its...
Hello, I recently acquired the thingy53 device and I am trying to use the example of the weather station with matter:
Weather Station . I am following what the documentation...
I've built a simple Matter device for the nRF52840, using the chip-build-nrf-platform Docker image.
The host OS is Linux, and I mapped the physical device ( /dev/ttyACM0...
Dear nordic,
state of your MCUBoot + Immutable bootloader is just awful.
Please fix this hook, when enabled it disables updates of the mcuboot bootloader when used with...
Hi,
From nRF5340 audio example kconfig, there is a note that "now 48kHz is the only sample rate supported". Is this correct? My application would only work for lower bitrate...
Hi,
I have a RIGADO BMD-300 module that can only be accessed over the air. (no physical access)
The modul has the BMDWare ( https://file.elecfans.com/web1/M00/20/D2/oYYBAFmk2JOADMegAAu4fGDEUUo022...
Hello,
I am looking at using the nRF52832 for a safety-related purpose and therefore want to isolate the safety-related code away from the Bluetooth stack. The main concern...
Hi,
I have observed a strange behavior when manually selecting wrong PLMN. I get EMM reject cause 11/PLMN not allowed as expected, but then the modem is stuck in CEREG state...
