Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi all.
Las Febuary 21, I received a Product Update Notification mail from Nordic, saying:
...We've just released a new version of the nRF Connect SDK, v1.9. This release...
Hi,
I'm trying to measure the communication distance with Coded PHY using two nRF52840s and the demo software below,
but there are some problems. They are shown below...
It has been about 4 years since I was developing for the nrf52840. During that time, it seems Nordic has moved to promoting the VS Code IDE vs. Segger Embedded Studio. If...
Hello,
I'm using the file app_update.bin of my project to execute a FOTA. I know that the first bytes indicates if the file is an application firmware, modem full or modem...
I was wondering if there was any documentation (graph or otherwise) that shows the efficiency of the DC/DC converter vs. supply current.
The product spec describes the...
https://devzone.nordicsemi.com/f/nordic-q-a/70679/call-to-nrf_sdh_enable_request-fails-in-sdk-v16-0-0-works-in-sdk-v15-3-0/291135?focus=true
I've been suffering from the...
Hello,
I want to implement the interrupt functionality and based on my understanding I can implement it using GPIO or ISR function.
In case of GPIO (APIs here ):
For...
Hello,
Is there a list of Android devices that will run nRF Connect, or will it run on any Android device?
Which Android app stores is it available in please?
Kind regards...
Hi,
We are using a module which includes nRF52832 in a custom board. After a while devices stop working but when we re-connect battery device starts working again exept...
Good morning,
I get a i2c nrfx twi error on startup and reset whenever the i2c sensor is switched off (<err> i2c_nrfx_twi: Error 195952641 occurred for message 0). I am...
Dear all,
I would like to ask if the nRF5340 LE audio can connect to a mobile device while another LE device is also connected to the mobile.
For example, is it possible...
Is it possibe to configure uart with baud rate of 512 on nrf52832?
I tried to configure the uart with this baud rate, but I am not able to get the uart communication ...
Hello everyone i need to update the Advertising Data of the device but i am not sure the correct way to do it. First i have the next struct of the Adv Data that i want to...
Thank you for your help. We are currently developing hardware using nrf52840. I would like to use pin numbers to control LED lighting, but when the port number is 0, I can...
I am developing a custom application that was started from 1 of the bluetooth examples for a customer and though I have been using the same custom PCB for 7 months, I am now...
