I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello
when hardfault is happaning, I can catch and understand the reset reason easilly, by looking at the map file
however, from time to time, I get a reset without...
I'm using Segger Embedded Studio version 1.6.0 to try to do some testing with SPI for a future project. Currently I am adding SPI functionality to the "Blinky" example: I...
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */
I am a beginner in this field. I am not sure what does this hexadecimal number...
Hi team:
After my device runs normally for more than 10 hours, the issue that THE socket cannot be created occasionally occurs. Once the issue occurs, the socket cannot...
Hi. I'm working on several projects, some of which are not using Nordic chips. I installed the latest Segger J-Link drivers to support a different project. I believe this...
Hi,
I am using nrf_drv_clock_hfclk_release (); in order to release the hfclk, before the call, the internal counter is 1 and the module is initialized.
because the counter...
I'm working on the NRF Connect SDK v1.6.1 and building the zephyr\samples\net\gsm_modem project, since I'm trying to set up and operate a Nimbelink modem. The code references...
Hi everyone,
I would like to change the output voltage and current driver strength of some GPIO ports on the nRF52840. I am using the zephyr driver "gpio.h" API, but the...
When I try to connect to a previously bonded device, I'm getting
Disconnected (reason 0x3d)
and bt_att: Unhandled ATT code 0x1d
and if I delete the bonds again and try...
I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1.
I am using a function in zboss_api called zb_secur_ic_get_list...
Hello,
I'm using SDK nrf5_17.0.2 on nrf52840
I'm implementing a custom nrf block device for a spi nand flash, and I'm getting trouble with the calling site of the nrf_blk_dev_read_req...
Hello Everyone,
I am using NRF52840 development kit, I have compiled the code using SDK15.0.0. I am using soft device as well. I have to implement flash protection in my...
Hi,
I’m finishing the design of a nRF5340-based custom board featuring a NFC coil-inductor antenna. Will orientation of track turns - clockwise or counterclockwise - affect...
