I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Dear sir,
Good Day!!.
Im using nrf52840 SDv16 and im using Ble_app_uart code, here with i need to add Bluetooth pairing request with password on my android mobile...
Hi,
I try to run the example project "ble_app_hids_keyboard" on a NRF52811 (I use the PCA10040e project, adapted to the NRF52811 on a custom board)
and I always run in...
Hi,
I was reading the values from the FICR of my nrf9160 on my thingy91 and I noticed that when I read the INFO.PART register from the FICR, it returned 0x00009120 rather...
we have BorderRouter- Raspberry pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI...
I am developing application with buttonles BLE DFU and FreeRTOS. I needed debounce on buttons and decided to use app_button. Here is my init:
I turn on log debug on app_timer...
Apologies for this question, as it has been asked a number of times but I've not found anything to help so far.
As at the time of writing, I believe I've got the latest...
I'm trying to deploy a new firmware to my hardware device but I get the following error in the nrf Connect 3.6.1 programmer (v1.4.8):
16:47:36.937
Error when getting...
Hi,
I noticed that the PPK2 turns off the internal voltage regulator upon disconnecting from it. Is there a possibility to change that behavior? I would like the voltage...
Hey Guys,
I have the nrf52840 as the peripheral and my application use varies depending on which central I am connecting to in terms of:
PC ( Windows or macOS or Linux...
Hello,
I have been recently trying to initialize fds in my application, through the assistance of the given flash_fds examples in the SDK (15.3).
Currently, I'm coming...
Hi, I'm working with flash, I've started with the example code from flash_storage, as I will need to use flash while using a SoftDevice.
I use NRF52 Dongle and SDK17.0.2...
hello,
i am using nrf52840 dvk with sx1276 lora modules and trying to read my device address using spi i am just calling the below function in main
uint8_t spiCommandData...
Hello everyone,
I'm currently working on porting a device driver to Zephyr on the nRF9160. I have defined a device tree and set up the device through the .overlay file...
Hi
I was wondering if there is any further reading about the Automatic network selection set as <mode> in the +COPS set command.
Especially, I'm looking for a solution...
