I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
I am developing an ESB application with 1 central (nrf52832 DK) and several peripheral. The peripheral are nrf52832 + ICM 20948. Development is done with Segger embedded...
I am trying to setup development environment by following below steps.
The nRF Connect SDK Zephyr repository contains a list of required Python modules. Install these modules...
Hi,
I have bought NRF24LE1 module. Now I want to program the module. So, will anybody please suggest me which programmer should I use to write hex file ? I have mPro programmer...
Hi,
I am currently trying to implement a beacon scanner alongside peripheral mode BLE on an nRF52832. As I am only scanning for beacons, I was hoping I would not need to...
I have been trying to connect to 4G using iBasis and other vendor's SIM card but have not been successful.
I have the nrf9160 DK two years ago and have been sparsely trying...
Hi,
We have 4 NRF52833 DK being used for our development work.
Among that, 3 of them have stopped working and are not powering up.
They power up some times when connected...
Hi,
to develop a device driver in Zephyr for TI DAC80501, a 16-bit DAC, I2C interface,
I have to
1. add the dts child node under the i2c controller node
$i2c1...
I'm using the asset tracker project and I want to add in the ability to store information on the board. However when you include the littlefs file system you get a build error...
Hi Team,
We are using the nRF52840 board for our development purpose. We are using the external debugger(i-jet) for our development purpose.
We are able to connect the...
I have a firmware build that uses the nRF52832 (SoftDevice S132) to return a variety of read characteristics to an external device. So far so good. I can verify that the values...
hi ,
i want to use the pin p0.19， p0.20， p0.21， p0.20 as the spi‘s pin scl，cs,mosi,miso.
and i test in the project nRF5_SDK_16.0.0_98a08e2\examples\peripheral\spi
my...
hello,
I have a problem when using the example twi_sensor with nrf52832( nRF5_SDK_15.3.0_59ac345\examples\peripheral\twi_sensor\pca10040\blank\arm5_no_packs)
This example...
Hello,
I'm porting a code from NRF Connect 1.1 to 1.3. Previously I was able to show in the console floats or double values, but now this seems not be possible anymore....
On SDK16.0.0 + Mesh SDK 4.1.0
I am trying to store some user data using the Flash Manager. I am modifying the light switch server mesh example.
There are a lot of posts...
Hi everyone,
I modified example code ble_apps_bps and introduced a GPIO interrupt, I want to sniff I2c communication (bit banging) but my ISR is triggered with a very long...
