After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
I'm using nrf52840 with BLE functionality.
I don't use sd_ble_gap_tx_power_set in my application.
Does it mean that I'm using default power (dbm)?
What is the...
Hi,
i am trying to interface an external spi flash memory with nrf52832 to store temp. data.
i tried to read the manufacture/device id but i am getting wrong data.
my...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
Hi
I am currently evaluating a 52840-DK (from 2017 I believe) and several 52840 dongles (ordered very recently). I managed to successfully run the light/switch mesh example...
Hello,
I'm trying to port the radio synchronization to a nRF5340. For this i need to use a DPPI group that clear a timer and disable itself for doing the task only 1 time...
I'm getting an undocumented status value back from nrfjprog when I try to program my dev board:
ERROR: command exited with status 3221225477 : nrfjprog --program C:/mdsg...
Hi,
I'm new to Nordic tools and am stuck on getting all the pieces in place. I have:
Mac OS 10.14.6
nRF Connect v3.6.1 Getting Started Assistant
Python 3.6.3
All...
Hey Guys,
Transferring emulated project
Transferring an emulated project to the nRF52810 SoC,
If you have developed your application using the emulated project...
Hello,
I am trying to setup a Project with nrf25840 by using the nRF IEEE 802.15.4 radio driver in multiprotocol mode with ble. ( https://github.com/NordicSemiconductor...
Hii guys ,
I have a customised nrf module based on nrf52810 . I have dumped ble_app_beacon code and it works fine but when i dump ble_app_uart example code then i am not...
Hi
I have a question about peers deleting.
It is saying in documentation about pm_peer_delete:
"Warning Use this function only when not connected to or connectable for...
hi Support team,
I have one problem with window7 system both 32 bit and 64 bit, that the usb cdc driver can not be verified by windows, that software signature is not right...
hi support team,
customer has one question about TWI electricity. in the IIC spec the "tLow " should be more than 1.3 us
however, our chip interface TWI timing " tLow...
