Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
It seems that the PEER ID is managed by the PEER MANAGER. Can I manage this information myself? For example, I save this information (ADDR IRK) after the connection event...
Using SDK 15.2.0, s132, nRF52-DK.
The logging facility in Segger Embedded Studio tells me that the call to nrf_sdh_enable_request() takes about 500 ms. I have an interrupt...
Hi,
I was following your guide to implement a secure boot chain ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_bootloader.html ) and therefore build...
Hello,
I have a simple question. So, I'm trying to write some manufacturing information into the UICR but once I write to these addresses I can't see the device via bluetooth...
Hello,
I am using the UBLOX EVK-NINA-B406, which has the nrf52833. I have attempted to use Softdevice S140 and S113 (using the nrfConnect programmer. Soft device versions...
I want to interface the nRF5340-PDK board to a different vendor's board that runs at 3.3V.
I'm using the SPI bus to communicate between the two boards
Using the nRF5340...
I don't have absolute proof yet, but I'm 90% certain that the carrier LWM2M (0.8.1+build1) has a memory leak when used with a +CEREG notification level higher than it is expecting...
After much searching this site for a solution I'm at a point were I decided it necessary for me to ask directly.
SDK16.0, S132, windows 10 / SES, nrf52DK
I'm able to connect...
Hello, To contextualize my questions, here is my project : I am working on a mesh network with a proprietary protocol. Each node is stationary. I use the nRF52832 SoC.I use...
Hi everyone!
My simple question is: why does this page no longer available? https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/how-to-connect-nrf91-to-google...
2020-06-08 16:20:39.229628+0530 OperationApp[3306:1831777] [Bearer] Central Manager state changed to .poweredOn
2020-06-08 16:20:39.635195+0530 OperationApp[3306:1831777...
How to add two or more custom characteristics in a custom service? I am able to add characteristics from github.com/.../nRF52-Bluetooth-Course to this tutorial. The same way...
Hello,
I want to start with BLE Mesh development. Therefore I have downloaded the Mesh SDK Version 4.1.0 from the Website and started to build everything. But I have a problem...
Hi I'm using the PCA10056 DK and ran into an issue. I can configure the nrf52 to wake up using input pins(although some pins can't wake it up for some reason), however, when...
