we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
It would be great if I could move my project over to the Mac and use one less computer. But I wonder how well the tools work on MacOS platform. Are there any major limitations...
Hello,
the "Developing for nRF52810" user guide in the Infocenter says that to fully transfer a project to nRF52810 the defines DEVELOP_IN_NRF52832 and NRFX_COREDEP_DELAY_US_LOOP_CYCLES...
Hi
i am new with nRF52832. i am trying to run fatfs example program. But it shows Disk initialization failed. what is the reason for it?.
i am using segger embedded studio...
Hi,
I'm using SDK 15.2 & trying to combine hid keyboard with custom gatt service, but it was not advertising. When I debug, it got stuck on the line below with error code...
Hi.
I'd like to use nRF52840 in our project. Can I use the SoC and Zigbee SDK for commercial?
UPDATE!
Have I any limits if I will use SOC and Zigbee SDK for commercial...
Hello,
I follow " Configuring and performing DFU over Mesh" instraction and face with error after trying to transfer new app: "No response after opening COM port".
I do...
Hi,
I am trying to merge dfu with Beacon application. I have added all the required file in dfu example, but I am getting linker error for bsp.o file.
I am using sdk 14...
m_cb.adc_state is set to NRF_SAADC_STATE_CALIBRATION inside the function nrfx_saadc_calibrate_offset(), but the value is never changed to NRF_SAADC_STATE_IDLE, even is the...
Hello
I'm trying connect central to 4 peripheralPeripheral has 3 different customization services. When I connected to 4 peripheral, I encountered the problem of service...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I want to place the section of the FLASH area arbitrarily. And, for example, I want to place the following...
There is now a TI CC2451 Bluetooth module as a reference. Using nRF connect to monitor the log content, it is found that when the mobile phone is connected to Bluetooth and...
Hi everyone, I have a question about GPIOTE.
What happens if for example, GPIOTE is used to configure a pin to detect a low to high transition, but the pin is already...
Hello
I have a problem with restarting advertising after disconnect event.
There are two scenarios:
In this case everything works fine:
I start advertising
...
Hello,
I started with the template app and tried to do two things on a nRF52832 using Segger Studio:
1) advertise custom service
2) use Application Timer and App Scheduler...
Cannot connect to nRF52840DK board using nRF Connect Bluetooth Low Energy app on Linux (Ubuntu 18.04 LTS). When I choose "Select Device" and choose my board, I get:
"Validating...
