Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi:
I already updated the SDK to the first release version V1.0.0 and the unit works well with NB-IoT, UART and SPI. I'd like now to include real GPS data but I can't get...
Hello, I'm working on programming a cycle to measure the power consumption. I need to send a message and wait for a response for some time, then shut the modem off, no matter...
Hi,
We were planning to use a spectrum analyser in order to do the radio test on the nrf52-dk. Where should the analyzer be connected? Should it be connected to the J1...
Hello, I'm trying to test the UART example for nRF 9160 DK. To my understanding, any input sent through one of the ports should appear in the other one (from uart1 to uart0...
I would like to use PSM to save power consumption of nRF9160 LTE module. However, if I use PSM on the module, the module is dormant and not able to receive the command from...
Hi, this might be a trivial question but I'm struggling to find the solution. I want to configure the asset tracker application so that it works with real GPS data on the...
hello!
i am using my nrf52832 with s132 softdevice. basically the ble template with my services and charas.
i checked power consumption in sleep mode and observed something...
Adding a Network Coding Extension to CoAP for Large Resource Transfer
https://ieeexplore.ieee.org/document/7796871
Can I use this coding in your some SDK project?
...
Hi all,
I ned to test DTM in labview. In nRFgo Studio works fine, but I don't have any idea hoe to relize same test in labview. Could anyone help me please?
Thank you...
Hi,
I'm working on nrf9160 DK board version 0.8.5. I want to use analog pressure sensor and read data using GPIO input, however there is a little issue related to acceptable...
Hi,
I'm having issues maintain the connection to a MQTT server. I'm able to establish the connection, keeping this alive and pub/sub some massages, but after some time ...
Hello ?
I try to bluetooth 5.0 Le mode test
but nrf studio program is not supporte Le mode 2M bps
therefore i need to nRF DTM Tool for bluetooth 5.0 LE mode 2M bps test...
Hey, When I initialize the device information service as follow ，It seems that It does not work ，RTT View show There cause a Fatal error 。 But if I initialize one of them...
Hi, I'm provisioning mesh nodes using nrf_mesh APP. After I finished it and added device into mesh network, I have some questions in configuration process.
In nrf_mesh APP...
