I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi ,
I am using NRF52832 device and I am referring ble_central/ble_app_hrs_c app . in this example , there is secure data used(pairing and bonding information) for whitelist...
I would like to create a repo to house all our vendor-specific board support, applications, etc. outside the Nordic nrfConnect repositories as per the Zephyr workflow. However...
Hi, I am an internship student and so new at programming. I have a nRF51822 DK that includes;
2 x nRF51822 module
2 x BLE master dongle
J-Link Cortex emulator (Debugger...
Hello everyone,
We have an IoT device with the nRF52832 module installed. We are in pre-production and in the process of certification. Our laboratory (EMITECH) asks us...
Hello team, i use board nrf52832 and SDK15.3. in example ble_app_uart_c. BLE_NUS_C_EVT_DISCOVERY_COMPLETE event occurs only once, after losing the connection and reconnecting...
Is there an example for setting up a Segger Embedded Studio project for using an nRF52840 with Zephyr. The instructions on the Zephry site for adding Zephyr files to a project...
Hello,
We are currently designing a device that will use the GPS on the nRF9160, our implimentation will involve using sensors to trigger GPS measurements for the duration...
I am using an nRF52832 and the Nordic UART Service (NUS). I am using the example NUS code and the UART side is plugged into another microcontroller's UART. By default that...
I need to find rssi value of my mobile (using nrf blink app) using nrf52840 Dk.. So i generally don't have idea what changes to be made for ble_peripheral->ble_app_blinky...
Looking at different solutions to an asset tracking system I'll be working on as my senior project later this year (getting a head start so time isn't as much of an issue...
Hi,
I'm writing a driver for a Ublox cellular module, which will be communicating with the nRF5240 using UART. After going back and forth, I decided to go with the app_uart...
Hello, I am an intern at a startup company and ive been tasked with finding some information about the chip set we are using, specifically the bluetooth aspects. We are using...
Hello,
I just installed SEGGER Embedded Studio to build the light switch example for Bluetooth mesh.
I managed to successfully follow the quick start guide using 3 development...
Hello!
I managed to flash my Raytac dongle with debugging going using the SWD on a nrf52 DK. I am mainly working with SEGGER Embedded Studio and nRF Connect on Mac. However...
i m getting constant RSSI values 32 even if i move far or near
this is the same example code in ble_peripherals
I HAVE UPDATED MY CODE (i have printed the RSSI values...
