I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
In " nRF51 Series Reference Manual ", in TWI chapter, it is mentioned to configure the GPIO pins with drive strength S0D1, to secure correct signal levels on the pins used...
In my application I'd like to use nRF52810 due different reasons. Since we're still in evaluating phase, without even choose a brand and related EVK, I've some basic questions...
Hi,
I am adding "install codes" function to my products.
Questions are
1. How many entries can i add with "zb_secur_ic_add" at ZC site?
2. Can i retrieve mac/ic (install...
Hi,
We are starting to measure the power of our nrf52840 based design.
I'd like to establish the power number for Idle() , since system will be in Idle() most of the time...
Hi,
I"m using SDK 15.3.0 with an NRF52840 dev board. I'm trying to record the timings from an incoming IR signal. In doing so I'm using LPCOMP with an analog input pin to...
I am trying to use the RF5 BLE CLI (Nordic NUS driver).
I need a plug and play COM port for Windows, iOS, and OS/X. This has to work for a customer.
It pairs easily, but...
My team is in the process of developing a product that uses the Fanstel BC832 module and have been running into issues trying to implement buttlonless DFU in our application...
I'm developing a fingerprint-related project. When the finger touches, the fingerprint sensor generates a pulse signal. NRF52810 will triggers a GPIOTE callback, then wakeup...
I try to bonding func using ble_app_gls example.
just connect is fine.
here is ble_evt handler
for trying connect bonding, I use pm_handler_secure_on_connection(p_ble_evt...
Hello,
I would like to use the nRF52840 for a wearable. It should be powered by a lipo-battery with 3.7V. Therefore I would solder it to the VDDH and Ground Pin (VSS). Is...
Hello .
I try to connect my JLink to my nrf51422QFAA cunstom board. And I use J-Flash to test ifg it can readback and it is OK. But When I try to use nrfjprog, I got some...
We would like to create the boot settings page and merge it with the application and flash the merged hex file using J-Link and nrfjprog.exe in production.
Currently in...
Hi,
We are looking for a secure NFC solution for our application. We want to make sure the tag is secured (cannot duplicate) and the reader, which is a NRF52840, needs to...
I am using SES V4.18 with SDK 15.3.0.
In sdk_config.h, I have set APP_VERSION_MAJOR and APP_VERSION_MINOR etc...
Is it possible to add these numbers to the output file...
I recently added Mesh DFU support to a project that I'm working on but it's extremely slow. It will take at least 1 hour to update the network under ideal conditions but I...
