Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
We have a 52832 device that is showing some possible flash corruption during programming. Does the softdevice perform an integrity check on startup such that a corrupted softdevice...
Hi I am using nRF52832 .My application acts as central and Peripheral at the same time.
board acting as Central: scans and connect to peripherals without any error.
But...
Hi,
I'm using nrf52840 and a barcode reader by UART using softwareSerial.h library, it works fine. I am also using the bluefruit.h library to communicate by bluetooth that...
I'm modifying the DFU example app in SDK 15.3, for the nRF52840.
attempting to call fds_record_update or fds_record_write within the context of app/main.c ble_evt_handler...
nRF5_SDK_11.0.0_new\examples\ble_peripheral\experimental_ble_app_eddystone\pca10028\s130\arm5_no_packs
Using the above mentioned example on a custom board with nf51822....
Hi,
I am working on a custom board with the 52840 chip. The problem I'm facing is that when I plug in my custom board, Windows 10 immediately shows a USB malfunction error...
Before my 52840 acting as central is connecting, it scans with the following params list:
static ble_gap_scan_params_t const m_scan_params = { #ifdef BOARD_PCA10056 .extended...
Hi i am using nrf52840 DK and i am trying out sleep_mode after timeout happens. but i had a doubt in ble_adv_evt_idle i.e if i use this case the device goes into sleep and...
Dear all,
I have a problem.The DFU could not be performed due to a large size of the application around 300kB.
Platform : 52832;
SDK: SDK_11.0.0;
softdevice:s132.
If we edit the example code in seggar embedded, are the same changes done for the hex files of the same examples? IF not how do we change the code and put it in the dongle...
Hi,
I was following the instructions laid out in the "Configuring DFU over Mesh" guide in the nRF5 SDK for Mesh v3.1.0 ( https://infocenter.nordicsemi.com/topic/com.nordic...
Hello All,
I am working on nRF51822 custom board and i am not change it because it is customer requirement. Use IAR embedded workbanch IDE in windows 7. For reference...
This post mentions that only logical address 0 is supported for the coded PHY.
Is there any additional explanation for why this is? The OPS does not mention this.
...
Hello, I am working on a project based on a central/peripheral NUS application, with nRF51822 and SDK 12.3 .
I Want to know if the debit of data exchanging is lower when...
