Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I'm trying to create more groups in mesh.We know that all the nodes(servers) are divided into two groups called ODD and EVEN,so I want to create more groups.
I have changed...
I posted recently ( https://devzone.nordicsemi.com/f/nordic-q-a/40381/interfacing-with-mcp4725-with-twi-registers ) and after editing the post, I can no longer access it ...
Hello, boss, I used twi read/write data from others device, I find a strange problem, When in no-blocking mode, mainly loop use "sd_app_evt_wait" TWI can't write data to others...
Hi, all. I have been going through the mesh examples and have been able to do the light switching, dimming etc examples and have used the RTT as well as physical buttons to...
Hello everyone,
My problem is the next one :
I bought a Nema 17 stepper motor (this one : https://www.pololu.com/product/2267 ) and it’s driver (this one : https://www...
It appears to be an error in the function signature `sd_ble_gatts_hvx()`.
Since the call is made via software interrupt, the const qualifier is cast away regardless.
So...
I am trying to implement the HAL interface for USB devices in Mbed for the nRF52840. Mbed is currently on nRF SDK14.2 so I may not have all the most recent bug fixes for the...
Hi,
I would like to run a different LWM2M client other than leshan LWM2M. Could you please answer me following questions:
i) Can i run any other LWM2M client written in...
Hello,
To improve the performance of SAADC, I would like to isolate the SAADC from the bad effect of DC/DC and RF.
I assume that SAADC has some noise because of DC/DC...
SDK 15.2's scanning module tries to connect to advertising peers that pass filter criteria when the nrf_ble_scan_init_t connect_if_match field is set true even when the advertisement...
Hi Forum!
I have to understand NRF52 chip for my job! I used to work with STM32 before. It has "Interrupt" (e.g when I receive one byte via SPI, It generates one "SPI_Rx_Interrupt...
Hi, all. I would like some serious help. I have three nRF52840 boards and have been running all the examples from the blinky to light switch/dimming. I am, however, stuck...
Hi,
could you please explain me what nrf52840_peripherals library (located in nrfx folder) is actually doing and what do the numbers next to the definitions mean ?
I see...
Hello everybody, As part of the evaluation of the nrf52840, I have made range measurements. In the course of this I was also concerned with the question to what extent the...
