Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
The release notes for the S132 V2.0.0.0 SoftDevice indicate it's only compatible with silicon revisions C and 1.
I have several PCBAs that have the rev B silicon. Will...
Hi guys
First of all, I know nRFgo can be very convenient for application encryption, but in order to improve the mass production efficiency,I merged the application code...
Hi!
Goal: I want to send as much data as possible using CoAP.
I have connected a nRF52 (IoT-DK) to a Raspberry Pi using BLE and 6LoWPAN. The nRF52 is running the CoAP...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
With the latest nrfjprog from Nordic and latest J-Link software from Segger, I am still getting the error below.
$ nrfjprog -v
ERROR: JLinkARM DLL version used is too...
I am working on the ble mesh using nrf51822. I am able to read the mesh values using the nrf master control panel android software. But we want to make an android software...
the priority of my custom thread is lowest priority. but it's not possible to call hvx function.
in ble_app_hrs_freertos example,
a sd_ble_gatts_hvx function is called...
Hello,
Suppose I flash a device that uses the nrf52832 with a serial bootloader, SD and valid application, can I still write to UICR regions via a serial connection using...
The nRF UART Android app currently uses a non-monospaced font; so, for example, a '1' is a different width to a 'W'.
This makes it hard to view strings where the fields...
Hi. I'm beginner.
I want to use nRF51822xxAA chip on keil compiler.
project->Option->Target->IROM1 start, Size & IRAM1 start, size.
Please let me know IROM's start and...
Hi,
I'm using ble_app_hids_keyboard example as the base to develop my own application, but was found something really strange, the application seems never get into sleep...
