I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I am using the adc to sample a sensor and send this over the air.
For testing I used the simple_uart library and it works.
But now I don't need the uart connection and I...
HI,ALL
Is the scanning device always get the BLE_GAP_EVT_ADV_REPORT Event ?
my current project is
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_central\ble_app_uart_c...
Hi,
I'm using SD110, SDK 10.0.0, nRF51822
In my own application, I control 4 servo by pwm with Timer1 and Timer2,
and I have 2 buttons, each button is a flag for...
Hi now i"m working on nrf15882 ,i'm confused how to test ble_uart example?
when i connect to the device(nrf15822),the cellphone app always displays:connecting,
later...
I'm trying to get a hold of a few nrf905 dev boards. Most the ebay boards have "nrf905 (ptr8000+)". Is there any difference between these chips?
I'm assuming the ptr8000...
Hi,
I setup the nrf51 as in central mode and talking to an ARM Cortex mcu via spi bus with the NRF51 set to slave. The spi communication working fine, but when I star scanning...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_hrs_c" "ble_app_uart_c" as reference.
My peripheral's Service UUID = 000098000000100080000017FFE07A00.
I want to...
Hi,
We intend to use nRF5x as main uC for our upcoming 4 new design. (diff. kind of measurement devices)
Instead of qualifiying each new device, we have intended to...
Is there a list somewhere that correlates the NRF_FICR->CONFIGID value with the actual nRF51 variant?
I had orginally used the 16K Ram versions, but when Nordic release...
Hello,
I'm implementing long write function to my project.
I managed to get it working, but i can't send more than 68 bytes of data.
When i'm sending the data, I slice...
Is there a way to tell if the timer is running? There's a start task, and a stop task, but I'm not sure how to tell if a timer is currently running. The best thing I can think...
Hi!
I developed my application using nRF51 DK with nRF51422 QFACA10 chip on it, and everything works fine. But now i would like to program this application on nRF51822...
Hello,
sd_softdevice_enable never returns.
I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a custom...
hi,
I am using currently keil v5. and sdk5.2, softdevice s110 v6.2 for board PCA10028 by changing header file of broad nrf6310. And also when i have been compile dfu_dual_bank_ble_boot...
