I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi, I'm using SDK 7.2 and S110 7.1.
I haven't mirgrated to SDK 10 yet.
I'm using the HRS and bootloader (which uses dual bank and BLE OTA) example.
After I select...
I am using nRF51 with Softdevice S110 to do a BLE peripheral, I want to have pin-code authentication before central device (or android phone) can connect to the peripheral...
ble_app_hrs_rscs_relay.hex the application ble_app_hrs_rscs_relay in SDK v9 can run fine,but in SDK v10.0.0 it doesnt work,even when i debug , it cannot go to main, and i...
Hi.
I have troubles.
I'm using nRF52 DK and V0.9.0.
I'm making program that does TWI communication between MPU9250 what is 9-axis sensor.
error is false every time.
...
I'm having problems getting the DFU dual bank ble s110 example to work on my target. My custom BLE app on my target is running fine, so my hardware is all good, and the DFU...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
I'm using s132_nrf52_2.0.0-7.alpha_softdevice. I've verified that the soft device is enabled.
void rdi_set_gap_parameters(void)
{
uint32_t err_code;
ble_gap_conn_params_t...
Is there are working example of FreeRTOS running on the nRF52 using the S132 SoftDevice? I am trying to get a ble_hrs example running with a updated version of the FreeRTOS...
Hi,
We have a rev3 nrf51822 system running S110 v7.3 and using SDK6.1.0. We are having trouble tracking down a ~1mA baseline current consumption when in system on/low power...
I'm struggling to understand this strange issue. I have a firmware based on S110 SD on nRf51822-QFABA0, this firmware is still based on version 7.1.0. The application is based...
I'm working on a program which sends 20 kb of data (sending 16 byte at a time) with one condition which is that indication should be enabled first. the first function checks...
Hi. i use SDK 9.0.0 and S130_1.0.0.
I want to recieve data from My peripheral S110..
First, I try to recieve data using example "ble_app_uart_c_S120-master".
I could...
Conditions in www.nordicsemi.com/.../Why-can-Master-Control-Panel-not-find-my-Master-Emulator-Dongle have been met, ie all components of PCA10031 have installed successfully...
in the answer of this question it said that :
You are also not allowed to send a new
indication until the previous one is
confirmed. This is signaled by the
reception...
