Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I have 4 buttons in my circuit with a nRF51822QQAC (a RAYTAC MDBT40 module on a custom PCB), I am using a very simple printf to check which ones are pressed, the internal...
I've followed this for assistance, but I'm stuck:
https://devzone.nordicsemi.com/question/17846/nonvolatile-memory-access/
I can read from flash, but I can't write to...
Hi
I wrote a softdevice, bootloader and application using the nRFgo Studio.
When I turn on the device, bootloader_settings_t is all 0xFF so bootloader_app_is_valid returns...
I went to so many references and definitions of variables and functions but I can't seem to find where is decided to use either spi_master_0 or 1.. where is this magic config...
I am a freshman. And I am doing some research on BTLE by nRF51822-EK. I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Is there...
Hey,
For my project I wrote and tested (w/ nRF51 DK) all firmware in mbed. I also made a custom PCB w/ the nRF51822 CEAA chip based on the 4 layer reference design provided...
HI,all!
I want to know if BLE can send data to APP in form of String instead of Byte?(the examples all send in form of byte )
If it does can, can you mainly introduce...
Hey everyone,
I'm trying to print floating point numbers to the UART to debug my application. I know the nrf51 is doing the operations correctly because if I convert the...
Hi,
I'm using the following TI IC www.ti.com/.../tps62736 to get 3V from a LiPo battery. It has a VIN_OK pin that I can configure to alert of battery low level. The problem...
Hi,
I am trying to get even a basic ARM GCC example set up using the provided toolchain code, and am having a rough go at it.
First, what is the most recent, working...
In the s110_nrf51_8.0.0_migration-document.pdf, the ROM and RAM start and size for the v7.0.0 and v8.0.0 are specified as follows
s110_nrf51_8.0.0
IROM1 - Start...
What should the connection or other settings be to have a peripheral always connected? It is a bit contradictory for low energy device, however for a lost&found (link-loss...
Hi,
I just started on developing on the nrf51-DK. I started with blue_app_proximity, and I am trying to hack the immediate alert to do a toggle a led. I initialize the...
Hi,
I am trying to save/restore some configuration variables to/from the flash storage. If I do it using S110, it works perfectly fine and I can both store and read values...
