I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
Hello!
I am currently running into throughput problems while using the Nordic Uart Service (NUS).
I am building a project for a peripheral and wanted to test the possible...
Hello,
We are implementing BLE FOTA for nRF52832. For that trying to load nrfutil tool. Its downloaded from official website. python is also installed successfully. when...
Attribute reporting is automatically handled by the ZBOSS stack which generates the Report Attribute commands. Is it possible to set the Disable Default Response bit in the...
This is same what same as in my previous ticket
With nRF9160 Ozone solution worked just fine but when trying to debug nRF9161 with Ozone I receive error on Ozone Console...
Hello,
In an NCS/Zephyr nRF52840 project I'm using a 3rd party 'plain' cpp library code.
This 'plain' library (written for Linux/RPi) uses the traditional std::mutex...
Dear all:
I have viewed that matter support below Operating Systems from this link:
project-chip.github.io/.../BUILDING.html
Tested Operating Systems #
The build...
Hi engineer I am using two nRF52832 boards to test the communication between ble_peripheral and ble_central. The project used is ble_app_uart and ble_app_uart_c in SDK15.0...
hello Nordic
i am using nrf52832 and nrf52840, working with ncs v2.3.0
currently i am using the SMP service for DFU but i also want to use the service's property to...
I b ought three ebyte E104-BT5040U USB dongle but it doesn't work.
I was program a ebyte E104-BT5040U USB dongle using openocd。I use daplink (2023-8-24) and openocd 0...
Hi,
We have been trying to get the audio application to work using an external I2S microphone, but have recently run into the following problem when trying to send audio...
Hello Nordic,
I've been attempting to convert our system's TWIM implementation from the blocking to the non-blocking mode. I have been able to communicate fine with the...
Hi,
I have updated finally Segger Studio from version 7.22 to 8.14. Now I cannot compile the project. It ends with below error:
Build failed, exit status 0x1
Is something...
