Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I originally developed the product using the nRF5 SDK with C++. The functionality is already implemented, but due to high power consumption from the C++ version, I now plan...
Sadly not in the documentation and the sizes changes from 5.0.0. I did try using the 5.0.0 but it doesn't boot (could be another problem). Thought I'd ask anyhow.
I have managed to use 3 nrf5340 audio DKs one configured as Gateway and the other two as left and right headsets to stream stereo audio. My question is, what do I need to...
I’m working on an nRF52-based design where the device should remain in System ON low-power mode after an operation (SAADC sampling + BLE sync). After SAADC data collection...
Hello,
My application uses three nRF5340dk for LE Audio: two Unicast Servers and a Unicast Client. The Client scans for servers, establishes connections, performs discovery...
Hello, I'm using the nrf5340 Audio development kit with SDK Manager v2.9.0 and a micro SD card, and when I try to play the audio as indicated in the development example in...
Hi, I have the following situation:
I have a legacy C application that runs on the good old nRF5 SDK on NRF52840 with FreeRTOS. (No BLE on the application, but the bootloader...
I am trying to repurpose NFC1 and NFC2 pins for GPIO usage, but they do not function as GPIO, while other GPIO pins work correctly.
SDK: nRF Connect Bare-metal SDK v0...
Hi Team,
Below function returns error code as -5 and unable to write and read data from I2C peripheral.
err = i2c_write_read ( i2c_dev , addr , write_data , write_size...
Hi,
so i was using the NRF51822-QFAC with an external balun and this antenna chip 2450AT43A100E .
now i want to move to the nRF52832 chip and from what i read is that...
hi support team,
customer is ordering sims from network supplier, and i got one sim card, but after testing i found this sim card can't be recognized.
here is the modem...
Hi
We have developed a remote-control system where both the sender and receiver are built around nRF52840. Today, the SDK is sdk-17.1.0. We are now considering moving over...
Hi Nordic Team,
I would like to use a USB camera in my project with the nRF5340. Is this possible? If so, could you please share any reference documentation or example links...
Hello all,
I am currently using the nRF9160 DK for cellular uplink to our server for an evaluation. From the nRF connect software I use the provided firmware 'AT Host' and...
