I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hello,
I am deploying a thingy 91-x sensor outdoors to record acceleration data. I am reaching out requesting recommendations on what kind of solar panel would be able to...
Hello all,
I am trying to prove that I can compile and upload some simple code that I have written and run it successfully on an nrf52840.
I'm using an mdbt50q-db-40 development...
Dear Nordic Team, Does the nRF54L15's channel sounding function use the channel range of 79 channels (72 channels excluding the advertising channel) stated in the Bluetooth...
I just got my DK today and initially wrote the blink command to make the LED blink, which worked fine. Later, I wrote the AT command back, and the LED just keeps blinking...
I am developing a BLE mouse that can connect to 3 devices using nRF52840.
The sample code (peripheral_hids_mouse) allows simultaneous connection to multiple centrals....
Hello Team, We are currently building a circuit using nRF52840 CKAA (WLCSP -94) .We have configured P1.03 & P1.05 GPIO pins as UART_TX & RX . Kindly confirm if this pin or...
Hello, I am currently developing on the nRF54H20DK, which i have previously used v3.2.0-preview1 for. Everything works fine on v3.2.0-preview1. I have tried bumping to v3...
I am using the zephyr\samples\subsys\nvs example. By default the program stores data in internal flash in storage_partition. I would like to create a custom board file for...
I am using the peripheral_uart example. Now, our device tree seems to have crashed. Before the crash, I added the following configurations to prj.conf of the application core...
Hello,
I'm having some issues with the channel sounding on the nRF54L15. I'm using two nRF54L15-dk and two custom bords with the nRF54L15.I'm using SDK v3.0.2 for my software...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
