I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hallo,
I am currently trying to debug the Matter samples on the NRF5340 DK. They all work fine, but I have a problem with the "Thread Viewer" in VS Code while debugging...
I have cypress ble module that generates carrier with PRBS9 modulation and GFSK on 2408MHz. As a receiver I use nrf52 Dongle and nrf52 DK board. In RSSI viewer I can see signal...
Hello Before we just have to overwrite shouldAutoConnect to enable an automatic reconnection Is autoconnect supported on Android NRF toolbox 3.1.3 (kotlin implementation)...
Hello,
In order to reduce the consumption, I remove some sensors (physically from the board).
Should I change the SW ? Is there any discovery state required that should...
Hi Nordic,
1. I am using bl653_dvk board and (C:\ncs\v2.1.0-rc2\zephyr\samples\drivers\uart\echo_bot) is using for my sample
2. Here is i need to communicate with both...
Good day
sorry if it's not clear, it's a rare problem and I have difficulties to explain it but here goes:
I Have two boards - PCA10056 from nordic and nrf52840 Feather...
Hello,
We have a custom NRF52840 board that can be powered via both Battery and USB. The peripherals that are connected to the board require it to be in high power mode...
Hi,
Build an application without SD but with MBR. MBR is at address 0x0000 - 0x1000. Application is at 0x1000 - 0xF0000. At the beginning of the application is the ISR...
Hi
What is your maximum throughput experienced with Android devices over Bluetooth 5.0+?
On my side, I can reach 340 kbps from Android to a nrf52 based device while transferring...
Hello all,
Two same same nRF52820 modules are connected to two usb ports and they are easily flashed via Segger, namely selected via two JLink emulator numbers.
Two separate...
Dear sir/madam,
My question is: - can you recommend courses/books which can help us to more deeply understand the zephyr RTOS in conjunction with the nordic microcontroller...
Hi,
We are currently developing the nRF52833 (peripheral) with ncs v2.0.0. We would like to calculate the link budget of our system when different smartphones are used as...
Hello
I am working with nrf9160dk_nrf52840 and using the BLE of nrf52
I am using the peripheral uart sample code to send some custom data.
I am trying to send more than...
I am having trouble updating a product with the firmware update file using NRFconnect app for ios version 2.5.3 using iphone se 2020.
We have been running successful updates...
