Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I am trying to set the UUID definitions for the Windows Application Bluetooth Low Energy 3.0.0. The only doc availible is for v2.3.1.
I tried to follow the following steps...
I'm using nRF SDK 12.2.0 and the corresponding soft device. I control a I2C slave for which I use the TWI peripheral through the driver implemented in nrf_drv_twi.c. It happens...
Hi,
I trying to enable Hardware Key for mcuboot.
I do the following at mcuboot.conf
CONFIG_BOOT_HW_KEY =y
But I got the following error:
Do I miss something...
Hello, I test SAADC on nRF52810, when I short gound to AIN0, the output is 0 normally, and when I add nothing to Pin I0(AIN0), the output is around 1056(Figure0), however...
I'm using nrf52833 on custom board.
And I need to using RESET pin to GPIO for battery charging detection.
I found CONFIG_GPIO_AS_PINRESET is configuration RESET pin...
Hi,
This may be a basic question. I'm using NRF52840 DK and I'm trying to print some logs from timer callback function, however I havent been successful so far. Here is...
Hi all,
I am using nrf52840 with zephyr
The below link puts device in bootloader mode but with pressing button
I want to do it without pressing button
https://devzone...
Hi All,
I just recently updated to a Mac w/ Apple M1 silicon and am struggling to get my (previously working) scripts to work w/o error.
Specifically, this command/error...
I got an nrf5340-dk development kit. And when I connected it to the computer it was discovered by the computer. But, I could not either connect to it or program it.
I noticed...
Nordic,
We've been using the nRF52832 for many years now. We have a custom board that uses SWCLK and SWDIO to flash our NRF52. We're getting set for production and I am...
I have been developing and debugging this situation for a while. I discovered that the original advice didn't work. First; to get more than 2 client connections going, I had...
Hi teams,
I am testing Direction Finding beacon/scanner pairs with nRF52833 DKs.
With nRFConnect SDK v1.7.1, I started beacon/scanner pair and leave untouched for a few...
Sorry if the title of the post is a bit of a misnomer. I'm currently trying to switch IDEs. Previously I was using Eclipse, but it seems like Nordic completely wants to remove...
