After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Dear forum,
I want to achive low energy consumption for a BM833 (with crystal).
From the following thread, I could deduct, that running the softdevice, an average of 300...
Hi,
OS: Windows 10
SW used is Segger IDE, nrfCOnnect for desktop to program HW used is nRF 52480 dongle PCA10059
I am starting using nRF 52480 USB dongle, I need to...
I am working with nrf52840DK, SDK v17.1.0.
I compiled and downloaded the open bootloader project to the DK using SES (No errors and verification says OK). According to...
Hi,
We wanted to add an additional flash section to the linker.cmd file located in the zephyr folder of the project folder. However, when we make changes to the memory section...
We have a situation where the network core of the nRF5340 has been given control of Port 0/GPIO pin X (GPIO0->PIN_CFG[X].MCUSEL = 1 on the application core). The network core...
I have 2 dongles that I've somehow managed to brick (I don't remember the details on how i did it). One of them goes into DFU bootloader mode when I plug it in but shows up...
Hi,
I am modifying the code to asset_tracker_v2 on Thingy91 to send data to my own server instead of Azure / AWS / Nordic Cloud. I am getting error code -35 (EDEADLK) when...
The discussion in https://devzone.nordicsemi.com/f/nordic-q-a/79364/maximum-number-of-bytes-that-can-be-used-in-beacon-advertising suggests that we should be able to populate...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
Hi, I'm trying to implement a sleep mechanism in my app. I based my code on the Power Management Example.
I use a button to put the app to sleep and the same button to wake...
