Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Project (NCS v2.7.0):
We are working on an application that requires time synchronized sampling of sensor data from 4 nRF52840 devices. The sensor data is then streamed...
In the specs of npm1300 PS, it is suggested that the ADC can measure VBAT, VBAT_7V range, NTC, DIE_TEMP, VSYS, IBAT. However, in the interrupt configuration reported in 7...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi All,
we are deciding which chip to buy in order to make our AoA trasmitter (CTE packets).
According to https://www.nordicsemi.com/Products/Wireless/Bluetooth-Direction...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Hello forum ,
Here i tried to write and read from flash qspi w25q64 but read and write both are failed ..i m using nrf52840 kindly pls help me for read and write
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hello
I have a very strange problem
A custom nRF52840 board has a charge detect pin, P1.6
A gpio callback is installed to wake it up on charger connect/disconnect
...
