Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I made a code based on ble_app_uart_c which connects to a peripheral and once connected it can write or read data.
The code is supporting BLE4 (1M) and BLE5 (Long Range...
Dear Concern,
we have tried to configure the accelerometer LSM6DSO module through SPI interface using NRF52xx DK board. External Module was not configured properly...
Since the Online Power Profiler only supports 1M PHY, does a static power profile for coded PHY exist that shows the current levels for the full advertising length? I'd like...
hi
nRF5 SDK for Thread and Zigbee v4.1.0
need to build a simple sensor with analog input .
Referring to the simple sensor (binary input ), I did make a ZED simple binary...
i made a mesh network using cli ftd uart example and transfer data using udp portal
there comes a need for me to indicate reset command through switch and send reset command...
I have 2 devices connected, working in notification mode. Using the nRF Sniffer for Bluetooth LE I was able to check all the messages that are exchanged. When in close proximity...
Hi, We have chosen to put our project and "custom board" outside of the NCS-directory. And since the newer revisions of SES, the "Open nRF Connect SDK Project" dialog window...
Hi,
On the P eripheral , after establishing a connection with the Central , start the timer to send data to the Central (the timer interval is set to 500ms and stop after...
I'm trying to get Thingy91 works under either Mac OS or Linux. Neither of Programmer nor LTE Link Monitor doesn't work. Programmer complains about that device is not in MCU...
Hi everyone,
I'm reading the documentation about USBD and I have some questions about it.
1) What's the EasyDMA? Maybe I understand what it is but I am not sure so I ask...
We are able to form a openthread mesh using CLI-ftd examples.At present we have server communicating to Clint in UDP portal .Is there is any UART command which is meant for...
I'm implementing APN lookup based on MCC MNC, which I try to obtain from IMSI using AT+CIMI.
However, AT+CIMI it returns valid result only after trying to connect for...
Dear Sir,
How are you doing today?
My customer would like to know the hardware revision information for the nRF52832-QFAB-R
Please let me know if you need additional...
