I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine,...
Hello Within my Thread network, I have a lot of Thread devices (with a lot of routers). Every now and then I need to multicast data to the whole network (I use the address...
Hello,
I am trying to read BMI160 outputs using SPI protocol but I am struggling to get a successful build from my code.
The build fails at the first line of my code...
Hi,
I am trying to write a file in flash(nrf52840) at a particular address & after that i want to instruct DFU module to start FW update from that address?
Is there any...
What are the situations where a SoftDevice calls reset handler?
I have a somewhat heavy data collection (lots of event handling) and those things are logged via RTT backend...
Hello,
I developed an application on a BMD-300-EVAL. This is a evaluation platform with a BMD-300 module (nrf52832 chip + antenna + crystal +...) on it. The application...
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
Hi
The flash data retention time for nRF52832 have been specified for 10 years @ 40°C. Is there any data available what the retention time would be at higher temperatures...
We are developing tracking system for our ground floor car parking but couldn't able to get GPS location.. we install Nordic Thingy:91 inside the steel body. Please let us...
Hello guys,
We are developing nRF52840-based device that needs to act as both BLE Central and Peripheral.
Peripheral role:
In BLE Peripheral mode, nRF52840 should advertise...
I have a need to send pressure data form 1 device to 4 other devices , it is medical application , data rate is in such a way to be in human readable form, can i use nrf24l01...
