Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I'm using the USBD for HID keyboard on my nRF52840 and I'm trying to change the serial number. On my PC (Linux) the Serial number always appears as 0 using lsusb -v...
Hello there!
I'm developing an nrf52810-based device, which needs to be as small and simple as possible, pretty much like your nRF51822 Beacon Kit.
I've founded the nrf52...
I successfully tried the "beaconing" example from your Mesh SDK 310.
I noticed that moving
line 215 "adv_start();" in main.c
right after "ERROR_CHECK(mesh_stack_start...
Hi, I am using nRF5 SDK for Thread and Zigbee v3.0.0, and I want use NFC pin and RESET pin as inputs.
I wrote in my .emProject this preprocessor definition "CONFIG_NFCT_PINS_AS_GPIOS...
Dear All,
I know that the max. input on VDD is 3.6V. But as a rule of thumb, I normally try to stay below the max. rating. But this time I have a peripheral LDO with 3.6V...
Sorry： Use google translation
I am compiling sdk using keil 5.27，use compiler version 6, armclang,
but is error:
Undefined symbol __start_pwr_mgmt_data...
I know...
Hello,
I am trying to create a new project after add source files and header files . While compiling I got error like "device must be defined. see nrf.h.segger"
Kindly...
Hi,
I'm asking this becase it is not very clear about the PWM in Product Specification v1.6 for nRF24LE1 in the nRF24LE1_PS_v1.6.pdf mentioned the pwm Frequency-range from...
I am using nRF5_SDK_15.2.0_9412b96.And we have code written to interface ads1298r to nrf52 dk for acquiring ecg signal.But the strange is the code is compiling in all others...
Hi guys,
Do you have any suggestions on how I can lower the power consumption. I am currently connecting - sending data - disconnecting .
I have the following set the...
Hi,
I'm trying to receive large packets on uart, but is seems to read one byte at a time .
uart_fifo_read() always returns 1
why is that?
can it be changed ?
Hey guys, i recently bought a nrf52 DK to implement a gateway between a usb touch monitor to a device such as a android or a computer.my approach is recovering the hid raw...
I'm using the nrfx drivers of SDK 15.3.0 and want to poll for data using a synchronous UART. In order to check for data, I use the 'nrfx_uarte_rx_ready' function. However...
Hi,
The documentation seems scant and IDE behaving inconsistently with regards to how basic project management, adding source files, libraries etc to a NRF9160 project,...
